




拉菲2平台app下载【kok795.com】是亚洲最大自主品牌游戏平台,日韩、俄罗斯、欧美女优荷官,各个美艳动人,百万大奖等您来拿,拉菲2平台app官网领取各种活动优惠,无需申请自动到账!
Steel and aluminum have different chemical and physical properties, such as melting point, thermal expansion coefficient, elastic modulus, etc., when welding steel and aluminum with hot processing welding technology will face many problems, that is, aluminum and steel easy to form a very hard and brittle IMP phase (intermetallic phase), and the greater the welding heat input, the more IMP phase generated. This brittle phase severely destroys the joint's static and dynamic strength, as well as deteriorates the joint's plasticity. Their main physical differences are showed below:
Material | Melting point | Elastic modulus | Density (20℃) | Heat conductivity | Standard voltage (25℃) |
Steel | 1536°C | 20400 N/mm2 | 7.87 g/cm3 | 46 W/mK | -0.44 V |
Pure Aluminum | 660°C | 6750 N/mm2 | 2.7 g/cm3 | 222 W/mK | -2.34 V |
Iron can melts a portion of aluminum in the solid state, but when the aluminum content exceeds 12%, the crystal structure changes radically, forming FeAL(mesh), Fe3Al(mesh) mixtures that are very hard (250-520hv) and brittle. Further increase, if aluminum content in the iron Fe2Al (factor), Fe2Al5 (eta) and FeAl3 (theta) mixture is formed, which offer higher hardness (600-1100 HV) and higher brittleness. This brittle material results from the diffusion of iron in aluminum or aluminum in iron. When the electrochemical potential of two different materials is different, molecular diffusion occurs to compensate for the potential difference. The greater the potential difference (E~ 1.22v for iron and aluminum), the greater the diffusion trend.
However, when the thickness of IMP brittle phase of the welded joint is less than 10 m, its brittleness becomes less important and obvious. At this point, the performance of the workpiece mainly depends on the ductility of the base material. Corrosion is another major problem because the electrochemical potential of the two materials is quite different, leading to electrolysis (equivalent to a battery).Aluminum, on the other hand, has a low potential and a negative electrode, which corrodes with electrolysis. To sum up, the welding of steel and aluminum needs to meet two requirements:
IMP phase thickness at the joint < 10 m
To prevent corrosion of base material after welding
To achieve these two requirements, a low heat input process is required, followed by special wire or weld corrosion protection treatment.
CMT (Cold Metal Transfer) technology is developed on the basis of short-circuit transition, and its heat input is much lower than normal GMAW welding. The process is: the arc burns, the wire pushes forward until the droplet shortens, at which point the wire feed speed reverses, the wire pulls back, and the current and voltage are almost zero. After the next circuit is formed, the arc rekindles, and the droplet transition begins again before the wire is reattached. The average frequency of this feed/pull back motion is up to 70Hz.
The success is based on galvanized steel and aluminum,the welding experiment is as follows: aluminum thickness range is 0.8 3 mm, filling material for aluminum silicon material, by melting aluminum and zinc formed on the surface of the brazing steel weld joint. Basic experiment is completed in 1 mm on the joint of steel and aluminum. The following table is the average intensity of the test.
Material | Plate thickness | Wire type | Welding methods | Mean strength, MPa | ||
Aluminum plate | Galvanized steel sheet | Zine-layer thickness | ||||
AW6016 | DDS47G47GU | 7.5μm | 1+1mm | AlSi5/COX | CMT | 145 |
AW6016 | CS G 90 | 20μm | 1+1.5mm | AlSi5/COX | CMT | 166.7 |
AW5754 | DDS G40 | 10μm | 1+1mm | AlSi5/COX | CMT | 130.3 |
AW5182 | DDS G40 | 10μm | 1+1mm | CMT | 134.5 | |
AW5182 | CS G90 | 20μm | 1+1.5mm | AlSi5/COX | CMT | 175.13 |
Note: COX is a special type of AlSi5 welding wire whose corrosion sensitivity is much lower than that of AlSi5.
It is inevitable that there is some loss of strength in the heat-affected zone of CMT process. When welding heat-treated aluminum alloy (6000 series), the heat-affected zone strength will lose 30-40% due to precipitation crystallization into a mixed crystal structure. Therefore, the heat-affected zone of this joint is the weakest part, and the lowest tensile strength is about 60% of that of the aluminum-based material. For naturally hardened aluminum alloys (5000 series), the strength of the heat affected zone is also reduced due to recrystallization. The strength reduction is related to the heat input in the pretreatment and welding process. The fracture occurs mainly in the heat affected zone.
Experimental data show that welding of steel to aluminum is possible, although steel be galvanized and a special low energy welding process are the prerequisite for success. The welding joints show excellent tensile strength, corrosion resistance and fatigue resistance, and also prove that the value of IMP brittle phase is less than 2.5 m, which is the key to prevent the brittle fracture of steel and aluminum joint.
Previous: Nickel Alloys
Related 拉菲2平台app下载
- Fillet Welding Of 6005A Aluminum Alloy
- The HIC Tested Carbon Steel And Low...
- How Was The High-pressure Carbon Fi...
- A Brief Introduction Of 6005 And 60...
- The Types Of Connection With Valve ...
- Anti-fingerprint Coating On Stainle...
- 10 Common Questions When Welding 41...
- What’s The PREN Of Stainless Steel?
- Pipe Thread(PT) VS NPT
- Nickel Alloys
- A Brief Induction Of Super Duralumi...
- Difference Between Wrought And Cast...
- H Temper Strain Hardening Codes For...
- The Comparison Of 6063 T5 And 6063 T6
- ASTM A790 S32205 Duplex Stainless S...
- How To Weld 316L Stainless Steel Pipe?
- Wrought Aluminum Alloy Designation ...
- The Welding Methods Of Aluminum And...
- Welding Stick Materials For Aluminu...
- The Difference Between Stainless St...
Friend Link 拉菲2平台app下载 
小泽玛利亚 樱井步 苍井空 石黑京香 桃谷绘里香 白咲舞 川岛和津实 黑泽爱 樱井步 小泽爱丽丝 七濑茱莉亚 樱朱音 原千寻 若菜奈央 稻森丽奈 尾野真知子 友田真希 花野真衣 雪本芽衣 雨宫真贵 冲田杏梨 高阪保奈美 霞理沙 泽井芽衣 北野望 桃谷绘理香 橋本凉 波多野结衣 仁科百华 柚木提娜 长泽梓 大沢佑香 天海翼 前田香织 前田香织 二宫沙树 铃木里美 希崎杰西卡 麻仓优 麻美由真 原更沙 葵实野理 上原瑞穂 福山沙也加 铃木麻奈美 西野翔 神谷姬 希志爱野 琴乃 希崎杰西卡 秋元里奈 原干惠 杏树纱奈 佐藤遥希 Sato Haruki 前田香织 二宫沙树 仁科百华 樱木凛 秋元里奈 小泽爱丽丝 原纱央莉 浅井舞香 音羽雷恩 天海丽 大泽佑香 百合野もも 里美尤里娅 铃原爱蜜莉 美竹铃 吉沢明步 吉泽明步 早川濑里奈 美竹凉子 松岛枫 佐佐木希 樱井梨花 立花美凉 小泉彩 里美尤里娅 铃原爱蜜莉 美竹铃 松岛枫 佐佐木希 朝美穗香 上原结衣 纹舞兰